Installation
Handlebar console
The package includes:
– Handlebar clamp 1 pc.
– M4x16 A2-70 screw 2 pcs.
– M5x20 A2-70 screw 1 pc.
– D5 spring washer 1 pc.
– Rubber band 1 pc.
– Crank 1 pc.
Measure the diameter of the handlebar. The mount is suitable for handlebars with a diameter between 20 and 30 mm. If you want to install the mount on a bar with a diameter of less than 20 mm, you will need the additional MCC-120 adapter. This allows you to mount the holder on bars with a minimum diameter of 12 mm. More details: motochargebar.de/products
Place the mount onto the handlebar and insert the 2 M4 screws. Before tightening the screws, we recommend wrapping the rubber band under the clamp around the handlebar. This ensures a better grip and protects your polished or otherwise treated handlebar from damage. In addition, the rubber pad helps to reduce vibrations. You can then install the device you have selected for the mount.
Adjustable mirror mount
The package includes:
– Mirror mount base plate 1 pc.
– M5x20 A2-70 screws 3 pcs.
– D5 spring washers 2 pcs.
– Short extension 1 pc.
– Long extension 1 pc.
– M5 self-locking nut 1 pc.
Measure the size of the mirror bolt. The mount is designed for an M10 thread size. Most motorcycles have mirror bolts with this diameter.
Unscrew the mirror. Insert the mount into the mirror’s threaded hole, then screw the mirror back in place.
Clamp console
The package includes:
– Mount base plate 1 pc.
– M5x20 A2-70 screws 3 pcs.
– D5 spring washers 2 pcs.
– Short extension 1 pc.
– Long extension 1 pc.
– M5 self-locking nut 1 pc.
– M6 10 mm spacer set 2 pcs.
Measure the bolt spacing on the brake/clutch lever. The mount is suitable for a bolt spacing between 29.5 and 33.5 mm.
Loosen the screws that secure the lever. The mount is typically designed for use with cylindrical head screws. If the screws are countersunk, use the spacers included in the package. In this case, longer screws than the factory ones must be used. These are not included in this set.
Clamp console
The package includes:
– Mount base plate 1 pc.
– M5x20 A2-70 screws 3 pcs.
– D5 spring washers 2 pcs.
– Short extension 1 pc.
– Long extension 1 pc.
– M5 self-locking nut 1 pc.
– M6 10 mm spacer set 2 pcs.
Measure the bolt spacing on the brake/clutch lever. The mount is suitable for a bolt spacing between 29.5 and 33.5 mm.
Loosen the screws that secure the lever. The mount is typically designed for use with cylindrical head screws. If the screws are countersunk, use the spacers included in the package. In this case, longer screws than the factory ones must be used. These are not included in this set.
Brake fluid reservoir console
The package includes:
– Mount base plate 1 pc.
– M5x20 A2-70 screws 3 pcs.
– D5 spring washers 2 pcs.
– M5 cap nut 1 pc.
– Short extension 1 pc.
– Long extension 1 pc.
Measure the distance between the screws that secure the brake reservoir cover. The mount is suitable for a screw spacing between 36 and 73 mm. The screws can be M4 or M5. The cover is typically fitted with countersunk screws, which must be replaced with cylindrical head screws. A washer may also be required.
Place the mount onto the brake fluid reservoir. Then insert the new screws and tighten them. If necessary, you can adjust the position of your phone as desired using the included extension pieces.
Fork stem
The package includes:
– Handlebar stem mount 1 pc.
– M6x50 screw 1 pc.
– M5x20 A2-70 screws 3 pcs.
– D5 spring washers 2 pcs.
– M5 nut 1 pc.
– M4x6 countersunk screw 1 pc.
Measure the inner diameter of the central steering stem. The mount is available in 3 sizes: 14–18 mm, 18–22 mm, and 22–26 mm in diameter. Choose the mount size that fits your motorcycle.
MCC-106: 14–18 mm, MCC-107: 18–22 mm, MCC-108: 22–26 mm
Insert the mount into the hole. Then tighten the M6 mounting screw until the mount is securely fixed in the hole. Place the base on top and screw in the two M4 screws.
M8 console
The package includes:
– M8 mount 1 pc.
– M4x6 A2-70 screws 2 pcs.
– M5x20 A2-70 screws 3 pcs.
– D5 spring washers 2 pcs.
– Mount base piece 1 pc.
– M8x60 A2-70 screw 1 pc.
– M5 nut 1 pc.
The mount is designed for M8 screws that secure the handlebar. It is designed so that one of the screws can be replaced with a cylindrical head screw. The mount is suitable for screws with a head diameter of at least 13 mm and a depth of up to 15 mm. Of course, the mount can also be installed using any standard M8 screw.
Loosen the selected screw! Then install the mount using the longer screw. It is possible that a screw other than the one supplied may be required. The new screw must be 20 mm longer than the original.
Finally, attach the base piece to the mount using the supplied M4 screws.